Description

ADICO - L is a mild alkaline iquid, which contains inhibitors, anti-oxidant agents and other special substances.

It is odorless and non-fuming.

Application

ADICO - L is used for:

• Temporary protection of the metals and gives a surface passivation by creating a thin protective film against corrosion.
• After treatment of ferrous surfaces with acidic solutions for protection and passivation.

Directions of use

ADICO - L is used diluted in water in a ratio of 2 - 5 % depending of the hardness of the water and the desired results. For special purposes can be used as it is without dilution.

ADICO - L can be used by immersion, spray or swab and for better results we suggest the immersion method.

When ADICO - L is diluted in hot water (60 - 80 oC) the results are much better because the surface dries faster.

When ADICO - L is used after rust removing or plasma cutting operations all parts must be rinsed very well with water prior to apply ADICO - L.

ADICO-L is used 5% in water after acid cleaning to neutralize and passivate boilers, pipes, cooling systems, evaporators, etc.

Circulate the solution hot or cold for 2-3 hours and empty the system. If the solution is hot 50-60°C the results are better.

Note: ADICO - L is also available in a powder - form.

Description

ANTICORROSIVE-225 is a mild alkaline liquid which contains inhibitors, anti- oxidant agents and other special substances.

It is odorless, non fuming, non-toxic and may be used on metals that come in contact with food stuff.

Application

ANTICORROSIVE-225 is used for the temporary protection of all metals and gives also a passivate film which protects the surfaces against corrosion.

Directions of use

ANTICORROSIVE-225 is used diluted in water in a ratio of 2 - 5 % depending of the hardness of the water and the desired results. For special purposes ANTICORROSIVE – 225 can be used neat without dilution.

ANTICORROSIVE-225 can be used by immersion,spray or swab but for better results we suggest the immersion method.

When ANTICORROSIVE-225 is diluted in hot water (60 - 80 oC) the results are much better because the surface dries faster.

When ANTICORROSIVE-225 is used after the removal of rust from surfaces, all parts must be rinsed very well with water prior to apply ANTICORROSIVE-225 .

Description

PROTECTIVE OIL No 4 is a corrosion preventive compound specially designed to protect metals against rust and corrosion for indoor storage, semi-sheltered outdoor storage and shipment. When used as recommended PROTECTIVE OIL No 4 is easy and economical to apply and remove and provides a durable, long lasting, soft coating suitable for protecting metal surfaces against the elements of corrosive environment.

Advantages:

• Forms a corrosion resistant and salt water resistant protective film.
• Stops grinding by penetrating deep and lubricating, hinges, locks, mechanisms, threads, etc.
• After its application surfaces remain lubricated.
• Meets corrosion requirements of U.S. Military Specification MIL-C-16173E Type II soft film.

Product Characteristics:

Flash point: >200°C

Pour point: <-5°C

Viscosity (40°C): >25° cSt Specific gravity: 0.9 ± 0.01 gr/cm³

Intended Usage:

• For extended indoor protection of interior or exterior surfaces of machinery, instruments, bearings or materials with or without use of supplementary barrier materials.

• For outdoor protection of material for limited periods where metal temperatures do not reach levels that produce prohibitive flow of the corrosion preventive film.

Alternative Usage:

PROTECTIVE OIL No 4 can also be used for electric motors, outboard engines, distributors, spark plugs, relays, etc.

Directions for Use:

PROTECTIVE OIL No 4 is used in full strength by spray, immersion or swab. Allow

PROTECTIVE OIL No 4 to dry to form a protective anti-corrosive film.

Product Removal:

PROTECTIVE OIL No 4 is easily removed from parts by solvent wiping, steam gun cleaning or alkaline hot tank immersion.

Description

A fast acting water and moisture displacer fluid that quickly cleans and dries out machines, electrical and electronic equipment.

It is rust preventive (ultra thin film) and protects the surfaces from rust and corrosion.

It allows quick starting of wet ignition systems and electric motors and equipment without disassembly or removal.

It eliminates moisture from the electrical systems of various machines. Penetrates existing rust and forms a film to prevent further corrosion. Cleans and lubricates the surfaces it is applied.

Applications :

• Wet ignition systems on cars, trucks, ships, etc.
• Wet electric motors and starters in power plants, factories, shipboard, etc.
• Cutting tools, hand tools, micrometers and measurement instruments.
• Seagoing equipment and Outboard engines.
• Pumps and valves.
• Aviation equipment.
• Cleaning compound for bore of small arms and automatic aircraft weapons.

Specification :

This product meets the following U.S. military specification :

• MIL-C-81309 (COMPOUND CORROSION PREVENTIVE, WATER DISPLACING ULTRA THIN FILM)

• MIL-C-372 (CLEANING COMPOUND FOR BORE OF SMALL ARMS AND AUTOMATIC AIRCRAFT WEAPONS).

Usage :

It can be applied with spraying or brush. Do not wipe off the surface. As the product evaporates it leaves a protective soft film on the surface with the above advantages.